ProTech Star Wars Action Figure Supplies
(also GI Joe and Star Trek),
Protectors and Display Cases

Loose Action Figure Stands for POTF2 Figures (1995+)

These action figure stands are designed for use with newer, POTF2 Star Wars figures. These stands work by placing the figure on the peg of the stand. These stands work well by themselves or with our loose action figure stand up cases (see below). Also available in vintage version with larger pegs.

NOTE: These stands will work for ROTS figures, but I've been advised that the pegs are too long to fit in the figures' foot holes, so you would need to shorten the pegs (simply use a pair of clippers) slightly to get them to fit.

Dimensions: 2" diameter, the peg on these stands is 3/32nd of an inch in diameter.

Features: acid free.

Please note: Figures are not included, order is only for the protective holders.

Loose Action Figure Blister - Small -- Closeouts at a reduced price!

The small size, single piece design Small Action Figure Blisters works well with many of the vintage action figures.

These are also a good holder for standard size PEZ containers.

Dimensions: 4 1/2" long, 1 1/2" wide, and 1 1/4" deep (inner dimensions)

Features: acid free, hang tab for wall mounting.

Please note: Figures are not included, order is only for the protective holders.

IMPORTANT NOTE: We are currently out of stock on the blisters that we've been selling for several months, and won't be able to restock those for at least a couple months. In the meantime, I picked up a closeout from ProTech that is slightly different. The lip around the edge is almost non-existant (on the old style it was about an eighth of an inch). Also it has a recycling triangle on the front of the case. Because of the lack of the side lip you have to be more careful when opening and closing the blister, so keep that in mind if deciding whether or not to order.

While we continue to have the closeouts in stock, we're reducing the price significantly. When the original style is back in stock, I expect it to be at a higher price than before, because of the increases in the cost of oil and plastic. So stock up on these if you're just looking for basic protective storage for your loose figures

Loose Action Figure Blister - Large

The large size, single piece design Large Action Figure Blisters works well with larger sized vintage figures, POTF2 figures, and Episode I figures.

Dimensions: 4 1/2" long, 2 1/4" wide, and 1 1/4" deep (inner dimenstions)

Features: acid free, hang tab for wall mounting.

Please note: Figures are not included, order is only for the protective holders.

Loose Action Figure Stand Up Display Case

These cases are designed to go hand and hand with the Loose Action Figure Stands (see above). All you have to do is place an action figure on a ProTech action figure stand and then stand them in the loose stand up case. These hard, poly-styrene design cases will provide easy viewing and protection.

The stands that allow the figures to stand up straight are sold separately, see above for stands for vintage figures, or stands for newer figures.

Dimensions: 4 3/4" high, 2 1/2" diameter.

Features: acid free, crystal clear, stackable.

Please note: Figures are not included, order is only for the protective holders.

Deluxe Acrylic Case for Carded Star Wars Figures

These cases are for vintage and new Star Wars Figures (except for Episode III figures). These cases are the best solution for those high dollar key pieces. Hand made of crystal clear acrylic.

For Episode III figures, see below for the new style acrylic case.

Dimensions: 6 1/8" wide, 9" tall, and 2 1/2" deep, these will hold all the vintage figures as well as the newest ones including the AOTC figures with deeper bubbles (will not fit Ephant Mon).

Features: acid free, 1/4" solid acrylic design, crystal clear, will never yellow, hang tab for wall mounting. Top rail and side rails hold figure in place.

Please note: Figures are not included, order is only for the protective holders.

Deluxe Acrylic Case for Carded Episode III and 2006 Saga Star Wars Figures

These cases will accommodate all standard vintage and new (including Episode III) Star Wars Figures. These cases are the best solution for those high dollar key pieces. Hand made of crystal clear acrylic.

Dimensions: 6 1/8" wide, 9" tall, and 2 1/2" deep, these will hold not only the Episode III figures, but also all the vintage figures as well as the newest ones including the AOTC and Saga figures with deeper bubbles (will not fit Ephant Mon).

Features: acid free, 1/4" solid acrylic design, crystal clear, will never yellow, hang tab for wall mounting. Top rail keeps figure in place, but there are no side rails. The lack of side rails is the only difference between the acrylic case above and this one. They had to be eliminated because of the width of the bubble on the Episode III figures.

Please note: Figures are not included, order is only for the protective holders.

This beautiful case is made of ABS plastic, painted black, and finished off by a sliding acrylic front cover (slides to the left or to the right, depending on how you position the case).

Each compartment is the same size (2.1" wide x 4.9" high x 2.1" deep) and has an individual mirror back. The action figures can be mounted onto our action figure stands (sold separately) for stability.

Dimensions: 18" wide x 15.5" high x 2.625" deep. Features predrilled holes for wall hanging. Holds 24 figures. Figures in picture are not included.

Similar to the Star Case, this is the best protection you can buy for your Playmate figures. Out of stock for months, because the original mold was deteriorating, and cases made from that mold were not the normal quality Protech wants to put their name on, we invested in enough cases to convince the factory to rework the mold to again produce high quality Playmate cases.

Dimensions: 7 5/8" wide x 10 1/4" high x 2 1/8" deep.

Features: acid free, 25 mil construction, hang tab for wall mounting.

Please note: Figures are not included, order is only for the protective holders.

IMPORTANT NOTICE: For several years now, this has been an item that has been made to order, and we have to purchase several thousand at a time.. Due to the number of items we are currently storing in inventory, and the space required to store a large quantity of these cases, this is probably the last time we'll be having these produced for us. In other words, when these are gone, they are probably gone for good. If you'll be needing them, you should purchase now before it's too late.